TOPSTAR MATERIAL PREPARATION TECHNOLOGY

Dehumidifying Dryer
Technology for
Precision Molding

Stable dry air. Controlled heat.
A cleaner path from resin to molding.

Topstar 3-in-1 systems integrate dehumidifying, drying and conveying. Discover how rotor design, heat recovery and application-specific material paths support repeatable resin preparation.

3-IN-1 HONEYCOMB DRYING SYSTEM Topstar honeycomb dehumidifying dryer with drying hopper and integrated conveying
Dehumidify · Dry · Convey One integrated material preparation system
PROCESS-AIR DEW POINT ≤ −45°C TCDHE-25 / TCDHE-50
DRYING TEMPERATURE 70–160°C TCDHE-25 / TCDHE-50
OPTICAL-GRADE FILTRATION 0.3 μm 99.99% filtration efficiency
CONTROL COMMUNICATION RS485 MODBUS RTU protocol
01 / HONEYCOMB ROTOR & AIRFLOW

What keeps the drying
air consistently dry?

A low dew point matters only when the drying circuit can maintain it. Topstar combines rotor construction, thermal separation and improved sealing to reduce fluctuations and air leakage.

INSIDE THE DRYING SYSTEM
Cutaway of Topstar dryer showing rotor, drying hopper and internal air circuit
Integrated dehumidification, drying and conveying
Unpartitioned honeycomb rotor
01

Unpartitioned honeycomb rotor

The rotor structure reduces dew-point fluctuations during rotation, helping deliver a steadier supply of dry process air.

Three-zone rotor cover with offset airflow ports
02

Three-zone covers & offset ports

Three isolated zones in the upper and lower covers limit heat transfer. Offset inlet and outlet positions improve the dehumidification airflow path.

Topstar flanged drying-air distributor with perforated lower plate
03

Optimized drying-air distribution

A flanged upper plate and perforated lower plate assembly reduces welding and increases the effective drying area. Closer-fitting rotor gaskets help limit air leakage.

Is dew point the same as resin moisture?

No. Dew point describes moisture in the air. Verify the resin’s final moisture level separately, together with its drying temperature, residence time and airflow requirements.

02 / HEAT RECOVERY & DEMAND CONTROL

Recover useful heat.
Reduce unnecessary drying.

Energy performance depends on the selected configuration and operating conditions. Pair heat recovery with demand-based operation while maintaining the resin’s drying requirements.

Topstar multilayer plate heat exchanger

Multilayer plate heat exchanger

For honeycomb models of 100 kg and below with this air-cooled configuration, a multilayer plate heat exchanger recovers useful heat and removes the need for a cooling-water connection.

UP TO 60%

Combined energy savings

TCDHE with variable-frequency control and heat recovery.

01

Match airflow to demand

Variable-frequency control adapts operation to material use, reducing unnecessary fan and heating demand.

02

Protect prepared resin

Heat-preservation and anti-overdrying functions support production pauses and lower-demand periods. Availability varies by configuration.

Actual savings depend on resin, throughput, operating conditions and the selected configuration.

Seven-inch Topstar dryer control display

Process visibility, built into daily operation

7-inch touchscreen · Operating and alarm logs · One-week scheduling · RS485 / MODBUS RTU. Dew-point display and barcode material verification are optional on the automotive-lighting configuration.

03 / APPLICATION-SPECIFIC CONTAMINATION CONTROL

A clean resin path,
designed for the part.

Optical parts, automotive lighting and oil-containing materials bring different risks. Select the appropriate filtration and contact surfaces instead of assuming that one clean-air specification fits every resin.

Polished stainless material-contact surfaces inside a Topstar optical dryer Polished material-contact surfaces
0.3 μm × 99.99%
OPTICAL GRADE

Optical-grade closed circulation

High-efficiency filters in drying and conveying circuits, polished hoppers and pipes, optical-grade conveying hoses and non-contact material shutoff help reduce contamination. A fluidizing receiver uses air agitation to remove dust.

0.5 μm
AUTOMOTIVE LIGHTING

Automotive-lighting air filtration

The automotive-lighting configuration filters drying, conveying and make-up air. A dedicated filling port and sealed lid reduce exposure during refilling.

Oil
control
OIL-CONTAINING RESINS

Oil-resistant configuration for oily resins

Oil filters and a blower oil-drain port address oil contamination. Ask for an oil-resistant configuration when release agents, diffusion oils or modified additives may affect the drying system.

Specify the quality requirement first. For transparent parts and automotive lamps, record cleanliness and acceptance requirements in the technical agreement.
04 / SERIES & CONFIGURATION GUIDE

Choose the technology
around your material.

Start with the process requirement, then select a drying platform and its application-specific options. Cleanliness, energy management and additive compatibility call for different configurations.

Series / configuration Key technology What to confirm for your project
TCDE energy-saving type Customizable variable-frequency control, heat preservation and anti-overdrying functions. Material demand, compressed-air conditions and the required energy-saving package.
TCDH honeycomb rotor type Honeycomb dehumidification; optional heat recovery and high-performance rotor with a stated dew point down to −50°C. Required dew point, operating conditions and whether the high-performance rotor is included.
TCDHE honeycomb energy-saving type Variable-frequency control plus heat recovery; TCDHE-25 and TCDHE-50 have a specified dew point of ≤ −45°C. Hopper hold-up, drying residence time, airflow and installation requirements.
Optical-grade configuration 0.3 μm × 99.99% filtration, polished contact surfaces and a clean, closed material path. Dust sensitivity, transparent-part acceptance criteria and receiver configuration.
Automotive-lighting configuration 0.5 μm air filtration, sealed filling, layered protection and optional dew-point monitoring. Clean filling requirements, monitoring options and the agreed technical specification.
Oil-resistant configuration Oil filtration, a blower drain port and an enlarged dehumidification tower. Additive composition, oil carryover and the dew-point measurement location.
Compare like-for-like conditions.

Rotor dew point, material-side dew point and make-up-air dew point describe different measurement locations. Confirm the test location and operating conditions before comparing configurations.

05 / EQUIPMENT PROTECTION & SERVICE ACCESS

Protection built around
heat, airflow and operation.

The automotive-lighting configuration combines temperature protection, blower monitoring and separated electrical control layers. Confirm the protection package for the selected model.

01

Three layers of overtemperature protection

Temperature-sensor trips, a mechanical air-temperature cutout and a heater-wall cutout provide separate responses to overheating.

02

Monitor all three blowers

Current-transformer monitoring protects the drying, regeneration and conveying blowers against overload. Phase-sequence protection addresses incorrect rotation.

03

Separate electrical control layers

An isolation transformer, optocoupler and relay controls, and solid-state relay / contactor drives separate computing, control and power-drive circuits.

04

Design for routine service

Crimped wiring terminals support secure reconnection. A drain outlet on the cooling-water tank assists cleaning on water-cooled configurations.

Check the whole air path during maintenance

Inspect filters, seals, the rotor and material-contact surfaces according to the selected model’s maintenance instructions. Oil-resistant systems also require attention to oil filters and blower drains.

06 / MATERIAL-FIRST SELECTION

How should you choose
a dehumidifying dryer?

Start with the resin grade, hourly material use and required drying time. Then match dew point, temperature, cleanliness and plant utilities to the actual molding process.

01

Define the material

Resin grade, moisture target, glass-fiber content, regrind proportion and oil-containing additives.

02

Size for the process

Hourly consumption × required residence time provides an initial material-hold-up estimate. Validate usable capacity and bulk density.

03

Match the configuration

Confirm temperature, dew point, filtration, energy options, power supply and conveying distance.

Explore the configuration for your material

Precision resin drying

Confirm the resin supplier’s moisture target and drying conditions. Select hopper size from hourly material demand, required residence time and usable capacity.

Optical / transparent parts

Specify 0.3 μm × 99.99% filtration, polished contact surfaces, optical-grade hoses and non-contact shutoff. Record transparent-part quality requirements in the technical agreement.

Automotive lighting

Specify the 0.5 μm filtered drying, conveying and make-up air paths, sealed filling and polished surfaces. Confirm optional dew-point monitoring and protection functions.

Glass-fiber content above 5%

Add glass-fiber-resistant treatment. Confirm the resin grade, fiber loading and abrasion-protection requirements.

Regrind / recycled material

Evaluate a cyclone separator. Provide the regrind proportion and dust characteristics to match separation and receiver options.

Oil-containing material

Discuss the oil-resistant configuration, including an oil filter and blower drain port. Identify all oil-containing additives before selection.

07 / TECHNICAL SPECIFICATIONS

TCDHE model specifications.

Compare hopper capacity, airflow, installed power and installation dimensions. Use these data together with the resin’s required drying conditions to size the system.

Selection parameter TCDHE-25 TCDHE-50
Nominal hopper capacity 25 kg 50 kg
Dehumidifying airflow 78 m³/h 100 m³/h
Drying heater power 3 kW 3 kW
Drying blower power 0.4 kW 0.55 kW
Regeneration heater power 3 kW 3 kW
Regeneration blower power 0.2 kW 0.2 kW
Conveying blower power 1.1 kW 1.1 kW
Total rated power 7.9 kW 8.05 kW
Specified dew point ≤ −45°C ≤ −45°C
Drying temperature 70–160°C 70–160°C
System power supply 380 VAC, 3P/PE, 50 Hz 380 VAC, 3P/PE, 50 Hz
Control power supply 220 VAC, 1P/PE, 50 Hz 220 VAC, 1P/PE, 50 Hz
Power cable / length 4 × 2.5 mm² / 5 m 4 × 2.5 mm² / 5 m
Dimensions (L × W × H) 1080 × 750 × 1770 mm 1120 × 750 × 1920 mm
Machine weight 208 kg 222 kg
Material pipe diameter Ø38.1 mm Ø38.1 mm
Finish / materials SPCC: RAL7047 / RAL5012; SUS SPCC: RAL7047 / RAL5012; SUS

Hopper capacity is not hourly throughput. Rated power is not average energy consumption. Confirm resin-specific capacity, site utilities and final specifications with Topstar.

08 / APPLICATIONS & PROJECT EXPERIENCE

From material preparation
to the production floor.

Topstar supplies 3-in-1 drying systems within broader auxiliary-equipment projects. Match the dryer to the part, resin and production rhythm, then validate the complete process.

Topstar application photograph showing an injection molding production workshop Injection molding production environment
HOME APPLIANCES

Repeatable material preparation

Topstar has supplied 3-in-1 systems alongside mold temperature controllers to Galanz. Select drying capacity around actual resin consumption and residence time.

ELECTRONICS & PRECISION PARTS

Coordinate auxiliary equipment

Supply examples include Foxconn and Luxshare, with 3-in-1 systems among the auxiliary equipment. Confirm material changes, cleanliness and process-monitoring needs.

OPTICAL COMPONENTS

Evaluate the specialized drying route

Topstar has supplied nitrogen 3-in-1 equipment alongside high-temperature mold temperature controllers to Yutong Optical. Discuss whether an optical-grade or nitrogen configuration fits the resin and part.

Questions to resolve before specifying a dryer

What if the resin contains glass fiber or recycled material?

Topstar recommends glass-fiber-resistant treatment when glass-fiber content exceeds 5%, and a cyclone separator when regrind is used. Confirm abrasion protection and dust separation for the actual resin blend.

Can a 25 kg hopper support 25 kg/h production?

Not by capacity alone. Hopper sizing also depends on drying residence time, resin bulk density and usable fill level. For example, 10 kg/h with a required three-hour residence time needs at least 30 kg of material hold-up before design allowances; this is an illustrative calculation, not a model recommendation.

Does every model offer the same dew point and filtration?

No. The specifications for TCDHE-25 and TCDHE-50 list ≤ −45°C. Optical and automotive-lighting configurations have different filtration specifications. Confirm the selected model, measurement location and agreed operating conditions.

BUILD THE RIGHT MATERIAL PREPARATION PROCESS

Bring your resin requirements.
We’ll help match the configuration.

Prepare your resin grade, kg/h, moisture target and part-quality requirements.

Discuss Your Application

Get A Quick Quote