Home / What is a mould temperature controller?

What is a mould temperature controller?

2022/07/22 By Topstar

mould temperature controller 1

A mould temperature controller is a temperature-control device that circulates water or heat-transfer oil through a mould to heat it to the required operating temperature and maintain a controlled thermal state throughout production. During injection moulding, it helps ensure consistent mould filling, cooling, surface quality, and dimensional stability. In injection moulding production, the mould temperature controller regulates the mould’s thermal state, while the barrel heater and plastification control system control the upstream melt temperature. Mould temperature controllers are categorised into two types: water-type and oil-type (the discussion below focuses primarily on water-based mould temperature controllers).

Water-type mould temperature controllers suit a wide range of plastic processing applications, while oil-based mould temperature controllers offer an alternative for high-temperature requirements. When selecting the right equipment, consider temperature settings, circulation performance, cooling capacity, pressure, and process conditions.

How can temperature control be supported during the injection moulding process?

Temperature control in injection moulding involves both bringing the mould to the required temperature and removing the heat introduced by the molten plastic. Process stability depends on how efficiently the mould temperature controller circulates the heat-transfer medium through the mould’s runner system. Therefore, operators need to understand the phenomena observed during production and the circulation mechanisms involved, as this helps identify the key aspects the equipment must control.

How can temperature control be supported during the injection moulding process

Why are mould temperature controller necessary for plastics processing?

During injection moulding production, without stable mould temperature control, the process may vary between start-up and continuous production. The parameters needed to produce the first batch of conforming products may differ from those required after the mould has undergone multiple cycles and accumulated heat.

Mould temperature controllers help establish repeatable thermal conditions. If the mould surface temperature is too low, it may cause premature solidification of the melt, thereby hindering mould filling or reducing surface finish quality; conversely, excessively high temperatures may prolong cooling times and make demoulding more difficult; uneven heat removal may also lead to warping and dimensional deviations.

When managing injection moulding temperatures, check whether defects appear during start-up, develop after prolonged operation, or occur only in specific cavities. These patterns help distinguish between issues such as insufficient preheating, improper cooling or cycle imbalance. While mould temperature controllers support process stability, they cannot resolve all issues related to materials, moulds, or injection moulding parameter settings.

How does a water-type mould temperature controller work?

The operating principle is straightforward: the system regulates circulating water through the mould’s internal channels and controls heating or cooling based on the measured temperature. The reliability of this process depends on both the temperature control equipment and the design of the mould’s water channels.

How does a water-type mould temperature controller work

How does water circulation control mould temperature?

A water-type temperature control unit uses a pump to deliver heated water through supply pipes to the mould’s cooling or heating channels. After exchanging heat with the mould, the water flows back to the unit, where a sensor measures its temperature. The control system then activates the electric heater or cooling valve as required.

During start-up, the water-type temperature control unit adjusts the mould temperature to the predetermined operating temperature. During continuous injection moulding production, it offsets heat generated by the molten plastic and external heat loss. The PID control system helps to minimise fluctuations in water temperature relative to the setpoint; however, adjusting the setpoint alone cannot resolve issues such as blocked flow channels or poor balance in the mould’s water circuit. For equipment designed for pressurised high-temperature circulation, the water temperature may exceed the boiling point at atmospheric pressure. Such applications, however, require appropriate pressure-control devices, hoses, pipe fittings, and safety precautions.

Importance for injection moulding quality

Mould temperature influences polymer cavity filling, surface formation, and heat dissipation before demoulding. Rather than aiming for extremely high or low mould temperatures, many manufacturers focus on maintaining a consistent, repeatable temperature distribution that suits the material properties, mould design, and target production cycle.

Importance for injection moulding quality

How Does Mould Temperature Affect Part Quality and Moulding Cycle Times?

If the mould surface temperature is too low for the selected material and filling conditions, the melt may solidify prematurely, causing short shots, visible flow marks, or poor surface reproduction. If the temperature is too high, the part needs more time to cool before operators can safely remove it from the mould. Furthermore, temperature differences between cooling circuits may cause uneven shrinkage, warping and dimensional variations between cavities.

These effects are especially noticeable in micro-injection-moulded parts, thin-walled products, optical components, and high-gloss injection-moulded parts. However, mould temperature is not always the sole cause of defects. Melt temperature, injection speed, gate design, holding pressure, and cooling time can also affect the final product quality.

To carry out effective process validation, the supply and return water temperatures of the temperature control system should be recorded, the water flow in key circuits should be checked, and the mould surface temperature at selected locations should be measured. This data should then be compared with fluctuations in part dimensions, surface appearance and moulding cycle times. This approach directly links injection moulding temperature control to product quality.

How do Topstar’s mould temperature controllers meet different production requirements?

Topstar offers water-type mould temperature controllers with maximum temperatures of 120°C, 160°C and 180°C, available in both standard and high-flow configurations. For example, the TTWP-1210 model has an 8 kW heater and a maximum rated flow rate of 58 L/min; meanwhile, some high-flow 120°C models can achieve flow rates up to 366 L/min. For water-based models operating at higher temperatures, Topstar employs a circulation system design tailored to their specific operating conditions.

Topstar’s fourth-generation temperature control unit design seamlessly integrates hardware with temperature control and monitoring technologies. Depending on the model and configuration, these features include self-learning PID control, nickel-plated copper heating elements, pressure monitoring, gas-liquid separation, and ultrasonic flow monitoring. These functions improve temperature stability and enable timely issue detection before flow or pressure anomalies affect production.

For more technical details, refer to Topstar’s mould temperature control technology, including its water circulation architecture, gas-liquid separation technology, and monitoring functions. When comparing mould temperature controllers, you can first browse our product range and then inquire about specific optional configurations.

Delivering Stable Mould Temperature Control

Mould temperature control units maintain a stable thermal state within the mould during production by circulating a heat-transfer fluid through it. In injection moulding, they maintain the temperature conditions required for the moulding process, ensuring production consistency. Water-based temperature control units do this by circulating regulated water through the mould, supplying heat during preheating and removing excess heat when needed. When the unit’s temperature range, heating power and pump performance are properly matched to the mould circuit parameters, the temperature control unit helps to reduce defects caused by temperature issues and stabilise the moulding cycle.

 

Prev: Everything to know cnc laser cutting machine manufacturer

Next: Economist Zhou Qiren and the research team visited Topstar to explore the high-quality development of manufacturing

TRENDING POSTS

HOT TOPIC

Get A Quick Quote